1 aizvietošanas variants atrasts

Esošais Sūknis - Drenāža un kanalizācija

Ražotājs Pedrollo
Produkta nosaukums VXC4 55/100
Elektropieslēgums 3x400 V
Caurules pieslēgums Rp 100
Nominālā jauda P2 4 kW

Nomaiņas sūknis Apmaiņats komplekts

Produkta nosaukums Rexa FIT V10-428
Artikula Nr. 6081904
Elektropieslēgums 3x400 V
Caurules pieslēgums DN 100
Nominālā strāva 8,1 A
Nominālā jauda P2 3,5 kW
Šķidruma temperatūras diapazons +3 - +40 °C
Brīvā caurplūde 100

Komentāri

Iespējamas izmaiņas uzstādīšanā, nomaiņas sūknim ir novirzīts savienojuma diametrs.
Replacement pump has less motor power.

Produkta informācija
Rexa FIT V10-428

Rexa FIT V10-428
Artikula Nr. : 6081904

Your advantages
  • Ready-to-plug and immediately ready to go (A and P version)
  • Attached float switch (A-model) enables easy operation
  • Safe vortex hydraulics with large, free ball passage to prevent clogging during operation
  • Sealing chamber with optional external monitoring
  • Lightweight
Construction
Submersible sewage pump for intermittent operation for stationary and portable wet well installation.

Application
Pumping of:
  • Sewage containing faeces in accordance with EN 12050-1
  • Wastewater
Equipment/function
  • Winding temperature monitoring with bimetal strip
  • Optional external pencil electrode for sealing chamber control
Scope of delivery
  • Submersible sewage pump with 10 m cable
  • Cable version depending on the variant:
  • With bare cable ends (O)
  • With plug (P)
  • With float switch and plug (A)
  • Operating and maintenance manual
Technical data
  • Mains connection: 1~230 V, 50 Hz or 3~400 V, 50 Hz
  • Submerged operating mode: S1
  • Non-immersed operating mode: S2-15 min; S3 10%
  • Protection class: IP68
  • Insulation class: F
  • Fluid temperature: 3 – 40 °C, max. 60 °C for 3 min
  • Free passage: 50 / 65 / 80 mm
  • Cable length: 10 m
Materials
  • Motor housing: 1.4301
  • Hydraulics housing: EN-GJL 250
  • Impeller: EN-GJL 250
  • Static gaskets: NBR
  • Sealing on pump side: SiC/SiC
  • Sealing on motor side: C/MgSiO4
  • Shaft end: Stainless steel 1.4021
Description/construction
Submersible sewage pump as submersible monobloc unit for stationary and portable wet well installation in intermittent operation.

Hydraulics
The outlet on the pressure side is designed as horizontal flange connection. The maximum possible dry matter is 8 % (depending on the hydraulics). Vortex impellers are used as the impeller shape.

Motor
The motors available are surface-cooled motors in single-phase version (with built-in operating capacitor) and three-phase version for the direct starting. The waste heat is given off directly to the surrounding fluid via the motor housing. These motors can operated immersed in continuous duty (S1) and non-immersed in short-time duty (S2) or intermittent periodic duty (S3).

Furthermore the motors are equipped with thermal motor monitoring. This protects the motor windings against overheating. For units with single-phase AC motors this is built-in and switches automatically. I.e. if the motor is switched off due to overheating and then cools down it is automatically switched on again. Bimetallic strips are used for this as standard.

In addition the motor can be equipped with an external sealing chamber electrode for monitoring the oil barrier chamber. This signals if there is water ingress into the oil barrier chamber through the mechanical seal on the fluid side.

The connection cable has a length of 10 m as standard and is available in following versions:
  • With bare cable ends
  • With plug
  • With float switch and plug
Seal
There is a sealing chamber between the motor and hydraulics. This is filled with medicinal white oil. The fluid-side and motor-side seals are provided by two mechanical seals which rotate independently of each other.