1
aizvietošanas variants atrasts
Esošais Sūknis - Drenāža un kanalizācija
Ražotājs
Grundfos
Produkta nosaukums
UNILIFT AP12.50.11.A3
Elektropieslēgums
3x400 V
Caurules pieslēgums
G 50 inv.
Nomaiņas sūknis Apmaiņats komplekts
Produkta nosaukums
Padus UNI-M05A/T011-540/A
Artikula Nr.
6096625
Elektropieslēgums
3x400 V
Caurules pieslēgums
Rp 50
Nominālā strāva
3,2 A
Nominālā jauda P2
1,1 kW
Šķidruma temperatūras diapazons
+3 - +40 °C
Brīvā caurplūde
10
Komentāri
Iespējamas uzstādīšanas izmaiņas, nomaiņas sūknim ir atbilstošs savienojuma diametrs.
Produkta informācija
Padus UNI-M05A/T011-540/A
Padus UNI-M05A/T011-540/A
Artikula Nr.
: 6096625
Your advantages
- Exceptional reliability owing to corrosion-free hydraulics for universal applications and various fluids
- Easy installation thanks to its low weight, integrated capacitor at the AC motor and threaded flange
- Optimum efficiency and high operational reliability owing to improved hydraulics
- Quick maintenance facilitated by direct access to the sealing chamber and pump housing
- Long maintenance intervals thanks to double mechanical seal and large volume sealing chamber
- Clog-proof thanks to the integrated strainer
The Wilo-Padus UNI is the ideal entry-level model for wastewater transport in small commercial buildings. The pump can be used flexibly as a portable device or in a pump chamber. Hydraulics made from corrosion-free composite material provide high levels of reliability for universal use in the pumping of a diverse range of fluids. Installation is made very simple due to its low weight, integrated capacitor and threaded connection. A double mechanical seal and the large sealing chamber facilitate long maintenance intervals. Direct access to the most important components make maintenance work very convenient. By utilising Wilo-Control switchgears, the Wilo-Padus UNI can also be integrated into existing building management systems.
Construction
Submersible drainage pump for intermittent operation for portable wet well installation.
Application
Pumping of:
- Sewage not containing faeces (EN 12050-2)
- Wastewater
- Fluids with a pH value of > 4.5
- Material version "B": Aggressive fluids, e.g. lake/sea water, condensate, distilled water
- Winding temperature monitoring with bimetallic strip
- Ready-to-plug (versions A and P)
- Float switch (version A)
- Vertical float switch (version VA)
- Submersible drainage pump with 10 m cable
- Operating and maintenance manual
- Mains connection: 1~230 V, 50 Hz or 3~400 V, 50 Hz
- Submerged operating mode: S1
- Non-immersed operating mode: S2-15 min; S3 10%, S1 (Version "C")
- Pressure connection: G2
- Protection class: IP68
- Insulation class: F
- Fluid temperature: 3 – 40 °C, max. 60 °C for 3 min
- Free passage: 10 mm
- Cable length: 10 m
- Motor housing: 1.4301
- Hydraulics housing: PP-GF30 (copolymer)
- Impeller: PP-GF30 (copolymer)
- Static gaskets: NBR
- Sealing on pump side: SiC/SiC
- Sealing on motor side: C/Cr
- Shaft end: Stainless steel 1.4401
Description/construction
Submersible drainage pump as submersible monobloc unit for portable wet well installation.
Hydraulics
The outlets on the pressure side are designed as vertical threaded flange connections. Open multi-channel impellers are used as the impeller shape. A strainer is integrated at the hydraulics housing.
Motor
The available motors are surface-cooled motors or self-cooling motors in single-phase current version (with built-in operating capacitor) and three-phase current version for direct starting.
With the surface-cooled motors, the waste heat is given off directly to the surrounding fluid via the motor housing. These motors can operated immersed in continuous duty (S1) and non-immersed in short-time duty (S2) or intermittent periodic duty (S3).
With the self-cooling motors, the waste heat is given off to the fluid via the sheath flow cooling. The motors can be used in immersed state and in non-immersed state for continuous duty (S1).
Furthermore the motors are equipped with thermal motor monitoring. This protects the motor windings against overheating. For units with single-phase AC motors this is built-in and switches automatically. I.e. if the motor is switched off due to overheating and then cools down it is automatically switched on again. Bimetallic strips are used for this as standard.
The connection cable has a length of 10 m as standard and is available in following versions:
- With bare cable ends
- With plug
- With float switch and plug
The "VA" version is equipped with a vertical float switch. In this version, the switching level is preset by two floaters sitting on a threaded rod. It uses less space than conventional float switches and is perfect for use in tight manholes.
Seal
There is a sealing chamber between the motor and hydraulics. This is filled with medicinal white oil. The unit is sealed on the fluid and on the motor side by mechanical seals.
Wilo-Control MS-Lift 1x4
Artikula Nr.: 2539741
Microprocessor-controlled switchgear for level-dependent control of a submersible pump with float switch for level measurement. The parametrization is carried out using dip switches and potentiometers.
Wilo-Control MS-Lift 2x4
Artikula Nr.: 2539745
Microprocessor-controlled switchgear for level-dependent control of a submersible pump with float switch for level measurement. The parametrization is carried out using dip switches and potentiometers.
Wilo-Control EC-Lift 1x12
Artikula Nr.: 2543210
Microcontroller-controlled switchgear for level-dependent control of a submersible pump with analogue or digital signal transmitters. Individual parameters are entered via symbol-based menu navigation and an operating button.
Wilo-Control EC-Lift 2x12
Artikula Nr.: 2543220
Microcontroller-controlled switchgear for level-dependent control of a submersible pump with analogue or digital signal transmitters. Individual parameters are entered via symbol-based menu navigation and an operating button.
DRAIN ALARM
Artikula Nr.: 2545133
Network-independent alarm switchgear (self-charging power supply unit) for wall fixation with optical and acoustic alarm signal.
LEVEL SENSOR 0-1MWS, 10M CABLE
Artikula Nr.: 2519924
Level sensor with ATEX approval for level control in sewage water containing faeces. A level sensor is used here to measure the hydrostatic pressure in the medium and to convert it directly in the pressure transducer into an electrical signal by means of a diaphragm. The signal is transmitted to the switchgear and evaluated accordingly.
LEVEL SENSOR 0-2,5mWS, 10m CABLE
Artikula Nr.: 2519921
Level sensor with ATEX approval for level control in sewage water containing faeces. A level sensor is used here to measure the hydrostatic pressure in the medium and to convert it directly in the pressure transducer into an electrical signal by means of a diaphragm. The signal is transmitted to the switchgear and evaluated accordingly.
FLOAT SWITCH WA 65 (PSN-O) 5M
Artikula Nr.: 503211390
As a signal transmitter for the system switching, depending on the level of an open container or a cistern.
Switching points: up ON / down OFF
Switching points: up ON / down OFF
FLOAT SWITCH WA 65 (PSN-O) 10M +VP
Artikula Nr.: 503211893
As a signal transmitter for the system switching, depending on the level of an open container or a cistern.
Switching points: up ON / down OFF
Switching points: up ON / down OFF
FLOAT SWITCH MS 1
Artikula Nr.: 2004593
Float switches for level control devices as min./max switches for fluids that are aggressive or contain faeces, floats with the fluid and switches when tilted. Because of its construction and switching point, the float switch can exhibit only a very small hysteresis. This property cannot be changed, not even the length of the cable. In order to use the float switch, a switchgear with adjustable run-on time must be used. Switching: up "ON"/down "OFF"
Float switch WA KR1 S
Artikula Nr.: 6082807
As a signal transmitter for the system switching, depending on the level of an open container or a cistern.
Switching points: up ON / down OFF
Switching points: up ON / down OFF
