2
aizvietošanas varianti atrasti
Esošais Sūknis - Daudzpakāpju
Ražotājs
Pedrollo
Produkta nosaukums
JCRm 2C
Elektropieslēgums
1x230 V
Caurules pieslēgums
Rp 25 / Rp 25
Nominālā jauda P2
0,75 kW
Attālums no grīdas līdz centram
162 mm
Nomaiņas sūknis Apmaiņats komplekts
Produkta nosaukums
WJ 204 (IE2) 1~
Artikula Nr.
4262914
Elektropieslēgums
1x230 V
Caurules pieslēgums
Rp 25
Nominālā strāva
5,3 A
Nominālā jauda P2
1,0 kW
Komentāri
Iespējamas uzstādīšanas izmaiņas, nomaiņas sūknim ir atbilstošs savienojuma diametrs.
Replacement pump has higher motor power.
Produkta informācija
WJ 204 (IE2) 1~
WJ 204 (IE2) 1~
Artikula Nr.
: 4262914
Your advantages
- User-friendly thanks to its light weight, compact size and practical carrying handle
- High supply guarantee due to hydraulic output, self-priming up to 8 m; even at a low flow rate
- Robust stainless steel construction for durable operation, impeller, shaft and housing made of AISI 304
- IE3-IEC three-phase AC motor (≥ 0.75 kW)
Self-priming multistage centrifugal pumps.
Application
- Pumping water from wells
- Filling, pumping empty, transferring by pumping, irrigation and sprinkling
- As emergency pump for overflows
- With or without handle, depending on the version
- For single-phase motor (1~ 230 V):
- Connection cable with plug
- On/off switch
- Thermal motor protection switch
- Pump with or without carrying frame, depending on the version
- Installation and operating instructions
- Mains connection 1~230 V, 50 Hz or 3~400 V, 50 Hz
- Inlet pressure max 2 bar
- Fluid temperature max. +5 °C to +35 °C
- Max. operating pressure 6 bar
- Protection class IP44
- Suction- and pressure-side connection G 1
- Pump housing made of 1.4301 stainless steel
- Impeller made of 1.4301 stainless steel
- Shaft 1.4005 stainless steel
- Mechanical seal made of ceramic/carbon
- Diffuser/injector made of Noryl
- Seals made of NBR
Bracket HiControl
Artikula Nr.: 4027326
Wall bracket for mounting Wilo-HiControl 1-EK.
HiControl 1 -EK
Artikula Nr.: 4190895
The Wilo HiControl 1 series is used for water supply pumps to enable automatic operation.
- Simple installation
- Especially compact design makes it suitable for many types of installation locations
- High operational reliability due to electronic fault signal
- Protection of the connected pumps due to built-in protection against low water levels
- Simple operation due to clear operating state display
- No additional diaphragm pressure vessel required
- Perfect corrosion protection, due to rust-free materials
Nomaiņas sūknis Apmaiņats komplekts
Produkta nosaukums
HiMulti 3-25 P 1~
Artikula Nr.
4244149
Elektropieslēgums
1x230 V
Caurules pieslēgums
Rp 25
Nominālā strāva
3,3 A
Nominālā jauda P2
0,5 kW
Attālums no grīdas līdz centram
147 mm
Šķidruma temperatūras diapazons
+5 - +35 °C
Komentāri
Iespējamas uzstādīšanas izmaiņas, nomaiņas sūknim ir atbilstošs savienojuma diametrs.
Replacement pump has impeller made of PPE/PS-GF30.
Replacement pump has less motor power.
Replacement pump has pump housing made of PA6T/6I-GF40.
Produkta informācija
HiMulti 3-25 P 1~
HiMulti 3-25 P 1~
Artikula Nr.
: 4244149
Your advantages
- Simple: Wilo-Connector (electrical quick-connector), on/off switch, filling and emptying devices, larger foot fastening
- Efficient: Highly efficient hydraulics, low electricity consumption and very compact thanks to motor optimisation
- Economical: smaller motor for optimum fulfilment of requirements
- Low noise (noise level between 56 dBA and 64 dBA)
- Version as domestic pump (pump for domestic water supply) with new pump design
Multistage centrifugal pump in non-self-priming version (HiMulti 3) or self-priming version (HiMulti 3 P)
Application
- Water supply (drinking water approval in accordance with ACS / in S1-version also in accordance with WRAS)
- Sprinkling
- Irrigation and spraying
- Rainwater utilisation
- Directly flanged motor
- Thermal motor protection switch for version 1~230 V
- Pump
- Two plastic connectors with gaskets for manual connection to the pipes
- Wilo-Connector (electrical quick connector)
- Installation and operating instructions
- Mains connection: 1~230 V, 50 Hz
- Perm. fluid temperature: 0 °C to +40 °C (+55 °C for 10 min)
- Perm. ambient temperature: -15 °C to +40 °C
- Permissible storage temperature: -30 °C to +60 °C
- Max. permissible operating pressure: 8 bar
- Max. permissible inlet pressure: 3 bar
- Protection class: IP X4
- Suction side connection: Rp1
- Connection on pressure side: Rp1
- Pump housing in Technopolymer with ACS and WRAS drinking certifications
- Impellers and stage casing made of Noryl 30% GF with drinking water certification in accordance with ACS and WRAS
- Pump cover and shaft made of stainless steel
- Mechanical seal made of ceramic/carbon
Bracket HiControl
Artikula Nr.: 4027326
Wall bracket for mounting Wilo-HiControl 1-EK.
HiControl 1 -EK
Artikula Nr.: 4190895
The Wilo HiControl 1 series is used for water supply pumps to enable automatic operation.
- Simple installation
- Especially compact design makes it suitable for many types of installation locations
- High operational reliability due to electronic fault signal
- Protection of the connected pumps due to built-in protection against low water levels
- Simple operation due to clear operating state display
- No additional diaphragm pressure vessel required
- Perfect corrosion protection, due to rust-free materials
