Esošais Sūknis - Cirkulācija
Nomaiņas sūknis - Parastais Apmaiņats komplekts
Komentāri
Produkta informācija
DL 32/150-2,2/2
![](/storage/512/dl-200x180.png)
Your advantages
- Reduced life cycle costs through optimised efficiency
- Can be used flexibly in air-conditioning and cooling systems, with application benefits due to direct draining of condensate via optimised lantern design (patented)
- High standard of corrosion protection thanks to cataphoretic coating
- Main/standby mode or peak-load operation (by means of external auxiliary device)
Glanded twin-head pump in in-line design with flange connection.
Application
Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.
Scope of delivery
- Pump
- Installation and operating instructions
- Permissible temperature range -20 °C to +140 °C
- Mains connection 3~400 V, 50 Hz (others on request)
- Protection class IP 55
- Nominal diameter DN 32 to DN 200
- Max. operating pressure 16 bar
- Pump housing and lantern: Standard: EN-GJL-250
- Impeller: Standard: EN-GJL-200; special version: Bronze CuSn 10
- Shaft: 1.4122
- Mechanical seal: AQEGG; other mechanical seals on request
Single-stage, low-pressure twin-head pump in in-line design with:
- Switchover valve
- Mechanical seal
- Flange connection with pressure measuring connection R 1/8
- Lantern
- Coupling
- IEC standard motor
![](/storage/956/blindlock-200x180.png)
- Comes in a complete kit containing a lid and gasket.
![](/storage/961/motflansar-dn32-65-200x180.png)
- Made of steel.
- Counter flanges (weld) are delivered complete (in pairs) with bolt, nut and flange gasket.
![](/storage/2777/packning-dn-32-200x180.png)
- Thickness: 1 mm.
- Inner diameter: 43 mm.
- Outer diameter: 82 mm.
![](/storage/3063/givare-stratos-maxo-200x180.png)
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
![](/storage/3063/givare-stratos-maxo-200x180.png)
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
![](/storage/3063/givare-stratos-maxo-200x180.png)
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
![](/storage/2687/differenstryckssensor-200x180.png)
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
![](/storage/2687/differenstryckssensor-200x180.png)
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
![](/storage/2844/efc-200x180.png)
![](/storage/2737/kap-dl-1450-200x200.png)
![](/storage/2738/kap-dl-2900-200x200.png)
![](/storage/2727/kopplingsschema-ipl-il-200x200.png)