1
aizvietošanas variants atrasts
Esošais Sūknis - Cirkulācija
Ražotājs
Flygt, ITT, Lowara, Xylem
Produkta nosaukums
AL 1102/4-133
Kopējais garums
450 mm
Elektropieslēgums
3x400 V
Caurules pieslēgums
DN 100 PN10
Nomaiņas sūknis - Parastais Apmaiņats komplekts
Produkta nosaukums
IPL 80/125-0,75/4
Artikula Nr.
2121190
MEI
≥ 0,4
IE
3
Kopējais garums
360 mm
Elektropieslēgums
3x400 V
Caurules pieslēgums
DN 80 PN10
Nominālā strāva
1,90 A
Nominālā jauda P2
0,75 kW
Šķidruma temperatūras diapazons
-20 - +120 °C
Komentāri
Ievērībai: izmaiņas cauruļvadu sistēmā.
Produkta informācija
IPL 80/125-0,75/4
IPL 80/125-0,75/4
Artikula Nr.
: 2121190
Your advantages
- High standard of corrosion protection thanks to cataphoretic coating
- Standard condensate drainage holes in the motor housings and lanterns
- Series design: motor with one-piece shaft
- Version N: Standard motor V1 with stainless steel plug shaft
- Bidirectional, force-flushed mechanical seal
Glanded pump in in-line design with screwed connection or flange connection.
Application
Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.
Scope of delivery
- Pump
- Installation and operating instructions
- Permissible temperature range -20 °C to +120 °C
- Mains connection 3~400 V, 50 Hz (others on request)
- Protection class IP 55
- Nominal diameter Rp 1 to DN 100
- Max. operating pressure 10 bar (special version: 16 bar)
- Pump housing and lantern: EN-GJL-250
- Impeller: PPO fibreglass-reinforced EN-GJL-200 (depending on pump type)
- Shaft: 1.4021
- Mechanical seal: AQEGG; other mechanical seals on request
Single-stage, low-pressure centrifugal pump in in-line design with:
- Mechanical seal
- Flange connection with pressure measuring connection R 1/8
- Motor with one-piece shaft
COUNTER FLANGE KIT DN80 PN10
Artikula Nr.: 2105585
- Made of steel.
- Counter flanges (weld) are delivered complete (in pairs) with bolt, nut and flange gasket.
Flange gasket DN 80 PN6/10
Artikula Nr.: 2175880
- Thickness: 2 mm.
- Inner diameter: 90 mm.
- Outer diameter: 132 mm.
SWITCH BOX SK602N
Artikula Nr.: 2120444
Automatic reactivation of pump after power failure and automatic fault acknowledgement after cooling off of the motor.
Equipment/function:
- Full motor protection tripping unit for pumps with thermal winding contact (WSK)
- Switch on/off with integrated run signal light
- Terminals for external, potential-free activation/deactivation
- Connection terminal strip
SWITCH BOX SK622N
Artikula Nr.: 2120445
Automatic reactivation of pump after power failure and automatic fault acknowledgement after cooling off of the motor.
Equipment/function:
- Full motor protection tripping unit for pumps with thermal winding contact (WSK)
- Switch on/off with integrated run signal light
- Fault signal light
- Terminals for external, potential-free activation/deactivation
- Potential-free contacts for external run signal (SBM) and fault signal (SSM)
- Connection terminal strip
- Switchgear SK 622N
- 4 threaded cable connections M20
- Installation and operating instructions
Difference pressure sensor 10 m
Artikula Nr.: 2136454
The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 20 m
Artikula Nr.: 2136456
The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 40 m
Artikula Nr.: 2136458
The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 60 m
Artikula Nr.: 503184696
The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 100 m
Artikula Nr.: 503184799
The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Frekvences pārveidotājs EFC 0,75 kW 3~
Artikula Nr.: 2551148
