2 aizvietošanas varianti atrasti

Esošais Sūknis - Cirkulācija

Ražotājs Flygt, ITT, Lowara, Xylem
Produkta nosaukums AL 1053/2-110
Kopējais garums 280 mm
Elektropieslēgums 3x400 V
Caurules pieslēgums DN 50 PN10

Nomaiņas sūknis - Electronic Apmaiņats komplekts

Produkta nosaukums IP-E 50/105-0,75/2
Artikula Nr. 2158820
MEI ≥ 0,4
IE 4
Kopējais garums 280 mm
Elektropieslēgums 3x400 V
Caurules pieslēgums DN 50 PN10
Nominālā strāva 2,8 A
Nominālā jauda P2 0,75 kW
Šķidruma temperatūras diapazons -20 - +120 °C

Komentāri

Saderīgs, neveicot izmaiņas cauruļvadu sistēmā.

Produkta informācija
IP-E 50/105-0,75/2

IP-E 50/105-0,75/2
Artikula Nr.: 2158820

Your advantages
  • Energy savings due to integrated electronic power adjustment
  • Optional interfaces for bus communication using plug-in IF-Modules
  • Simple operation with Green Button Technology and display
  • Integrated dual pump management
  • Integrated full motor protection (PTC thermistor sensor) with trip electronics
Construction
Electronically controlled glanded single pump in in-line design with flange connection and automatic power adjustment.

Application
Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.

Equipment/function
Operating modes:
  • Δp-c for constant differential pressure
  • Δp-v for variable differential pressure
  • PID control
  • Constant speed (n=constant)
Manual operation level
  • Green button and display
Manual functions
  • Differential pressure setpoint setting
  • Setting the speed (manual control mode)
  • Setting the operating mode
  • Setting the pump ON/OFF
  • Configuration of all operating parameters
  • Fault acknowledgement
External control functions
  • "Overriding Off" control input
  • “External pump cycling” control input (effective only in dual pump operation)
  • Analogue input 0 – 10 V, 0 – 20 mA for constant speed (DDC) and remote setpoint adjustment
  • Analogue input 2 – 10 V, 4 – 20 mA for constant speed (DDC) and remote setpoint adjustment
  • Analogue input 0 – 10 V for actual value signal from pressure sensor
  • Analogue input 2 – 10 V, 0 – 20 mA, 4 – 20 mA for actual value signal from pressure sensor
Signal and display functions
  • Collective fault signal SSM
  • Collective run signal SBM
Data exchange
  • Infrared interface for wireless data exchange with IR-Monitor/IR-Stick
  • Plug-in position for Wilo IF-Modules (Modbus, BACnet, CAN, PLR, LON) for connection to building automation
Safety functions
  • Full motor protection with integrated trip electronics
  • Access disable
Dual pump management (twin-head pump or 2 x single pumps)
  • Main/standby operation (automatic fault-actuated switchover)
  • Pump cycling main/standby operation after 24 hours
  • Parallel operation
  • Parallel operation (efficiency-optimised peak-load activation and deactivation)
Scope of delivery
  • Pump
  • Installation and operating instructions
Technical data
  • Permissible temperature range -20 °C to +120 °C
  • Mains connection
  • 3~400 V ±10 %, 50 Hz
  • 3~380 V -5 % +10 %, 60 Hz
  • Protection class IP 55
  • Nominal diameter DN 32 to DN 80
  • Max. operating pressure 10 bar (special version: 16 bar)
Materials
  • Pump housing and lantern: EN-GJL-250
  • Impeller: PPO-GF30
  • Shaft: 1.4021
  • Mechanical seal: AQEGG; other mechanical seals on request
Description/construction
Single-stage, low-pressure centrifugal pump in in-line design with:
  • Mechanical seal
  • Flange connection
  • Drive with integrated electronic speed control
COUNTER FLANGE KIT DN50 PN10
Artikula Nr.: 2105581
Mating flanges:
  • Made of steel.
  • Counter flanges (weld) are delivered complete (in pairs) with bolt, nut and flange gasket.
Flange gasket DN 50 PN6/10
Artikula Nr.: 2150974
Flange gasket DN 50 PN6 / 10, Klingersil:
  • Thickness: 2 mm.
  • Inner diameter: 61 mm.
  • Outer diameter: 96 mm.
IR-Stick WILO Set
Artikula Nr.: 2109467
USB stick for wireless data exchange for all electronically controlled Wilo pumps with infra-red interface; can be adapted to any commercially-available Windows PCs/laptops with USB interface.
The IR-Stick in combination with the supplied Wilo software (CD-ROM), makes it possible to read out and save data records for pumps as well as send previously defined pump settings.
 
  • IR carrier frequency: 33 kHz / 455 kHz
  • Software upgrade: via USB
Particularly suitable for:
  • Inaccessibly installed pumps
  • Quick configuration of pumps
  • Extensive operating information
  • Detailed fault diagnosis
  • Statistical functions
  • Special settings/control modes for special requirements
  • Protection against unauthorised access
  • Archiving of pump data sets
IR-MONITOR (D,NL,GB,F)
Artikula Nr.: 2017390
Operating and service unit for wireless remote control and remote diagnosis for all Wilo pumps with infra-red interface.
For all pumps and standard motors for measuring the direction of rotation, rotating field frequency and current operating status.
Direction of rotation checking device also for all conventional pumps with alternating or three-phase motor.
Industrial standard due to its sturdy and robust plastic casing, graphical display with scratch-resistant monitor screen.
 
One-button manual operation level for the Wilo high-efficiency and energy-saving pumps, additional 4 buttons for:
  • IR-Monitor on/off
  • Lighting on/off
  • Information/help
Display/monitor (50 x 50 mm) for displaying:
  • Electrical and hydraulic actual values
  • Power supply and duty point of the pump
  • Statistical values
  • Service information
  • Device settings.
Test functions, such as:
  • Self-test pump
  • Self-test IR-Monitor
  • Battery status check.
IF-Module BACnet
Artikula Nr.: 2097811

Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key.
IF-Module CAN
Artikula Nr.: 2085044

Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key.
IF-Module LON
Artikula Nr.: 2022530

Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key.
IF-Module Modbus
Artikula Nr.: 2097809

Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key.

Nomaiņas sūknis - Parastais Apmaiņats komplekts

Produkta nosaukums IPL 50/105-0,75/2
Artikula Nr. 2152934
MEI ≥ 0,4
IE 3
Kopējais garums 280 mm
Elektropieslēgums 3x400 V
Caurules pieslēgums DN 50 PN10
Nominālā strāva 1,76 A
Nominālā jauda P2 0,75 kW
Šķidruma temperatūras diapazons -20 - +120 °C

Komentāri

Saderīgs, neveicot izmaiņas cauruļvadu sistēmā.

Produkta informācija
IPL 50/105-0,75/2

IPL 50/105-0,75/2
Artikula Nr.: 2152934

Your advantages
  • High standard of corrosion protection thanks to cataphoretic coating
  • Standard condensate drainage holes in the motor housings and lanterns
  • Series design: motor with one-piece shaft
  • Version N: Standard motor V1 with stainless steel plug shaft
  • Bidirectional, force-flushed mechanical seal
Construction
Glanded pump in in-line design with screwed connection or flange connection.

Application
Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.

Scope of delivery
  • Pump
  • Installation and operating instructions
Technical data
  • Permissible temperature range -20 °C to +120 °C
  • Mains connection 3~400 V, 50 Hz (others on request)
  • Protection class IP 55
  • Nominal diameter Rp 1 to DN 100
  • Max. operating pressure 10 bar (special version: 16 bar)
Materials
  • Pump housing and lantern: EN-GJL-250
  • Impeller: PPO fibreglass-reinforced EN-GJL-200 (depending on pump type)
  • Shaft: 1.4021
  • Mechanical seal: AQEGG; other mechanical seals on request
Description/construction
Single-stage, low-pressure centrifugal pump in in-line design with: 
  • Mechanical seal
  • Flange connection with pressure measuring connection R 1/8
  • Motor with one-piece shaft
COUNTER FLANGE KIT DN50 PN10
Artikula Nr.: 2105581
Mating flanges:
  • Made of steel.
  • Counter flanges (weld) are delivered complete (in pairs) with bolt, nut and flange gasket.
Flange gasket DN 50 PN6/10
Artikula Nr.: 2150974
Flange gasket DN 50 PN6 / 10, Klingersil:
  • Thickness: 2 mm.
  • Inner diameter: 61 mm.
  • Outer diameter: 96 mm.
SWITCH BOX SK602N
Artikula Nr.: 2120444
Wall-mounted unit for electrical connection of single-phase and three-phase pumps with integrated thermal winding contacts (WSK) for monitoring the winding temperature (full motor protection).
Automatic reactivation of pump after power failure and automatic fault acknowledgement after cooling off of the motor.

Equipment/function:
  • Full motor protection tripping unit for pumps with thermal winding contact (WSK)
  • Switch on/off with integrated run signal light
  • Terminals for external, potential-free activation/deactivation
  • Connection terminal strip
SWITCH BOX SK622N
Artikula Nr.: 2120445
Wall-mounted unit for electrical connection of single-phase and three-phase pumps with integrated thermal winding contacts (WSK) for monitoring the winding temperature (full motor protection) and external run/fault signal.
Automatic reactivation of pump after power failure and automatic fault acknowledgement after cooling off of the motor.

Equipment/function:
  • Full motor protection tripping unit for pumps with thermal winding contact (WSK)
  • Switch on/off with integrated run signal light
  • Fault signal light
  • Terminals for external, potential-free activation/deactivation
  • Potential-free contacts for external run signal (SBM) and fault signal (SSM)
  • Connection terminal strip
Scope of delivery:
  • Switchgear SK 622N
  • 4 threaded cable connections M20
  • Installation and operating instructions
Difference pressure sensor 10 m
Artikula Nr.: 2136454

The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 20 m
Artikula Nr.: 2136456

The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 40 m
Artikula Nr.: 2136458

The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 60 m
Artikula Nr.: 503184696

The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Difference pressure sensor 100 m
Artikula Nr.: 503184799

The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.
Frekvences pārveidotājs EFC 0,75 kW 3~
Artikula Nr.: 2551148